How to set up ExpressVPN on a TP-Link router with L2TP

This tutorial will show you how to set up a VPN on your TP-Link router with the L2TP protocol.

The steps in this guide were tested on the TL-R600VPN and AC1750 Archer C7 models. The L2TP setup may not work for all TP-Link router models.

Additionally, some TP-Link routers only allow IP addresses instead of ExpressVPN server names. ExpressVPN cannot provide IP addresses for setup on those routers. If you encounter difficulties with your specific TP-Link router model, contact the ExpressVPN Support Team for immediate assistance.

Note: The router used in the video is the TP-Link AC1750 Archer C7.

Before you begin, you may wish to make a note of your default internet settings. This will help you revert to your original internet settings when the VPN is not required.

1. Find your ExpressVPN account credentials

Go to the ExpressVPN setup page. If prompted, enter your ExpressVPN credentials and click Sign In.

Enter the verification code that is sent to your email.

On the right, select PPTP & L2TP/IPsec.

This will show you your username, password, and a list of server addresses around the world.

Keep this browser window open. You will need this information for the setup later.

Need help? Contact the ExpressVPN Support Team for immediate assistance.

Back to top

2. Configure your TP-Link router with the VPN

Each TP-Link router firmware version has its own user interface.

To find out which user interface your firmware version is associated with, enter 192.168.0.1 in your web browser and log in with your username and password. Then refer to the appropriate section which matches your user interface below.

Note: If your TP-Link router runs on an older firmware version such as TL-WR940N (c 3.16.9 Build 150312 Rel.59597n), refer to these steps to set up on older firmware.

In your browser’s address bar, enter the IP address for the router admin panel. By default, this is 192.168.0.1. (If your router’s IP address was changed in the past, and you cannot remember it, you can find it in your device’s settings.)

Log in with your router’s username and password. (By default, both are admin.)

At the top of the page, click the Advanced tab.

In the sidebar, go to Network > Internet.

Set Internet Connection Type to L2TP.

Enter the following information:

• Username: Paste the manual configuration username you found earlier.
• Password: Paste the manual configuration password you found earlier.
• VPN Server IP/Domain Name: Paste the manual configuration server address you found earlier.

Set Secondary Connection to Dynamic IP.

Leave MTU Size at 1460 (the default).

Set Connection Mode to Manually.

Set Max Idle Time to 0 minutes.

Click Connect.

Click Save to save all your settings.

Configure your TP-Link router (older firmware) with the VPN

In your browser’s address bar, enter the IP address for the router admin panel. By default, this is 192.168.0.1. (If your router IP address was changed in the past and you cannot remember it, you can find it in your device’s settings.)

Log in with your router’s username and password. (By default, both are admin.)

In the sidebar, click Network > WAN.

Set WAN Connection Type to L2TP/Russia L2TP.

Enter the following information:

• Username: Paste the manual configuration username you found earlier.
• Password: Paste the manual configuration password you found earlier.
• Confirm Password: Paste the same manual configuration password again.
• Server IP Address/Name: Paste the manual configuration server address you found earlier.

Set Secondary Connection to Dynamic IP.

Leave MTU Size at 1460 (the default).

Set Max Idle time to 0 minutes.

Set Connection Mode to Connect Manually.

Click Connect and Save.

Need help? Contact the ExpressVPN Support Team for immediate assistance.

Back to top

Disconnect from the VPN server

To disconnect from the VPN server, click on the Advanced tab.

In the sidebar, go to Network > Internet.

Near the bottom of the page, click Disconnect.

Need help? Contact the ExpressVPN Support Team for immediate assistance.

Back to top